Mastering the vacuum pump safety matters _ five o 'clock

vacuum pump five security matters, to master the essential

a, pay attention to the personal safety

in order to install the vacuum pump at the scene, in the operation of the vacuum pump in addition to pay attention to safety, also a general preventive measures should be taken, to ensure that the vacuum pump in the work environment health and safety. No matter where the machine run, want to wear the right clothes. Repair electric pump, also must wear insulating gloves and helmets. If you work or the percentage of pumping station and sewage treatment, please be sure to make a waterproof tape wrapped, and wrapped it, or you will direct contact with the waste water, through a wound or eyes, mouth membrane infection, may be infected with a serious virus, if injured at the scene, should immediately use waterproof, disinfection and cotton bandage. Please note the following:

1, the operation process, the experiment operating personnel shall not carry electronic products.

2, experiment operating personnel should wear special vacuum equipment operating gloves, not direct contact with the vacuum equipment.

3 attachments should be stored in a drying oven, vacuum pump equipment, away from corrosive chemical gas or liquid.

4, should be regular cleaning vacuum pump equipment, should choose when cleaning dust-free paper or clean cloth with alcohol or acetone.

5, the laboratory should insist on degrees must be dry, the operator should check daily laboratory humidity and temperature conditions.

6, the laboratory should maintain good ventilation, to avoid the impact of mechanical vacuum pump oil and gas.

7, the operator should pay attention to the temperature of the vacuum pump equipment use, to avoid overheating and shorten the service life of the instrument.

8, the operator should be after the molecular pump speed below the line, will be put into molecular nitrogen gas or liquid nitrogen pump.

9, the operator should pay close attention to the loss of high pressure pump power supply interface, to prevent the operator to get an electric shock, to ensure safety.

10, trial operation, should be in strict accordance with the operation steps of the vacuum equipment switch valve, prevent reverse pumping caused by pressure difference.

11 don't experiment, when the alarm rang, and immediately notify the lab and maintenance personnel to check.

12, in case of special circumstances, should immediately inform all attendees leave quickly, and cut off the vacuum power supply equipment.

2, pay attention to ventilation experts know pump need ventilation in order to prevent the body from overheating. Therefore, the pump installation location must ensure that adequate ventilation and prevent fire risk. This means that all pump types other than the submersible pump must be installed in at least three feet away from the walls and other equipment. In addition, the pump from the waste gas containing CO called toxic and tasteless gas, carbon monoxide is a chemical reaction is not completely. Usually use fuel engine will release carbon monoxide, so the fuel pump in the completely closed space exists potential safety hazard. Therefore, it is important to make sure that all the fuel pump in the expansion space can be fully ventilated. Three, pay attention to the overheating

check suction strainer, ensure it is not blocked, to eliminate the security problems of pump, prolong the service life of pump. Make sure pump enough air flow to cool the engine, but some one vacuum pump often from time to time without any direct cause overheating. In this case, the pump operator must do one thing, stop immediately, and let the cooling pump. Direct contact with the hot pump can cause severe burns or burns, so you must stay away from overheating pump, until you are cooled to room temperature. The cooling time depends on the size and temperature of the pump, sometimes for up to 2 - 3 hours. Only when the operator to confirm the pump has cooled completely, can open the drain plug. When the pump is too hot, in any case is impossible to remove the cover plate, plug, packing or drain plug. Such behavior will not only endanger the operator himself, it can kill the others around. Four, the types of vacuum pump

the different types of pumps with different security risks. Therefore, you must know you of the specific conditions of the water pump operation, operation points for attention, etc. , especially for new employees, if there is any uncertainty, should first consultation, enter a step confirmed the type of pump.

5, vacuum pump motor motor driven pump must be properly grounded, to reduce the risk of employees get an electric shock. If improperly installed, the pump may be short circuit, vacuum pumping station staff has the responsibility to ensure that all electrical devices in accordance with national and local electrical code.

vacuum pump needs to be installed correctly. Different regions have different request for grounding line. Hire a qualified staff operating electric pump are equally important. Before the repair electric pump, must make sure to cut off the circuit. Similarly, if in the process of the motor running, line tripping, one must solve, please professional electrician check and then restart the vacuum pump.

However, water pump isn't the only producer in domestic, and many people feel that J&T INDUSTRY CO.,LTD.'s service leaves much to be desired in terms of functionality and design.
To build customers value by delivering high-quality products, services and solutions in innovative and cost effective ways. J&T INDUSTRY CO.,LTD. will realize this mission by setting the highest standards in service, reliability, safety and cost containment in our industry.
To properly understand what customers want, when, why and how they want it, J&T INDUSTRY CO.,LTD. needs to pivot toward sentiment analysis, a burgeoning technology that taps into consumer demand based on natural language processing.
The more people who do a certain thing, the more likely others are to do it as well. When JT can demonstrate their popularity or satisfaction across a wide customer base, other consumers are more likely to buy in as well.
Our company specializes in manufacturing water pump mainly pool cover drain pump.