Circulating pump installation where the most appropriate, heating circulation pump home installation is right

Heating is people are used to in the cold winter, if no heating, that will be very cold in winter. His burning heating in the family, it need to use central heating circulation pump, can accelerate the flow of circulation, improve the heating hot water flow rate, better heating effect, let the room temperature is improved. Home heating circulation pump is mainly aimed at the heating of the users, or large family home heating system cycle, floor heating hot water cycle use.

home heating circulation pump can be installed in any position of central heating conduit, for example, can be installed in the kitchen, storage room, etc. ; But usually we install home heating circulation pump is cultured, take a look at the specific introduction, correct installation of household heating circulation water pump, to achieve better effect.

home heating cycle before the pump installation check:

if you can feed water temperature, water temperature is low, installation of circulating pump can solve the problem, but if the return water temperature is low, so need to find out the reason is not hot. In general, this kind of pump is installed on the return water pipe, get rid of a pipeline on the original system, pump string to the piping.

home heating circulation pump installation connected the power running in a few minutes, first ( Check whether the boot normally) Not too long, but idle time ( 5 seconds) To prevent dry running effect of the ceramic bearing life.

before heating circulation pump pump installation, shall ensure that pipeline without slag quality, if there are any impurities, welding slag, dirt, etc will cause damage to the pump life; For the first time when using please pay attention to the exhaust pump, the pump cavity has plays a role of the pressurization air, you can. Used for hot water circulation continuous operation time to a week or so, exhaust time.

to begin, to check the circulation pump inlet and outlet, are there any foreign matter or see some dust, to clear in time, don't have to block a circulating pump. Before installing the into heating system to heat pipe cleaning time, avoid the pipe inside the foreign body into the circulating pump of, affect the circulating pump.

installation, don't use too much effort, to prevent excessive force, the circulating pump damage. In the position of circulating pump inlet and outlet, to install can interface, so that we can convenient disassembly.

the power cord, to install the three pin plug with ground wire, ground wire and connected to the shell of the circulating pump, so that we can avoid the dangerous situation when in use, make more safety when using circulating pump.

circulating pump in use is largely mute, there won't be any noise, so if you want to see opened, circulating pump is in operation, can use a screwdriver to as the tool, on the edge of the ear to listen to, don't directly near the circulating pump to the ear.

home heating circulation pump installation location:

1. Home heating circulation pump - - Installed in the nozzle position, starting from the water flow is the place to be pressure, so that we can accelerate the flow of the cycle. The installation method, it is widely used here is more easy, and there is a problem can be handled in time, more convenient.

        2. Home heating circulation pump - - In the middle of the heating pipe installation, so that we can have the effect of acceleration on the middle of the flow. Especially in a large area of the bedroom, best installed in the middle, because when the water from the water entry into has great speed, but in the middle section will slow down, reduce the speed of the cycle. In this location to install a circulating pump can let the water continued to maintain rapid cycling, achieve better heating effect.

        3. Home heating circulation water pump - - Installed in the outlet, this also is a good place, because it is out of the water temperature is low, tonggu cycle can make the water quickly to the heating area, and then enter the next cycle, indoor temperature can be effectively improved.

        4. Home heating circulation pump - - Install where is not obvious, so we can play a beautiful effect. Many people choose to install the circulating pump in the bedroom, so we can have very good beautification effect. But there will be noise in the bedroom, have an impact on sleep quality. Advice can be placed in toilet, both to achieve good compression effect, at the same time also does not cause the attention of others.

if you are using radiator heating way, at this time suggest that we choose to use for the next time cycle, namely hot water supply pipeline from wall-mounted boiler water supply, water supply pipeline along the roof installation, from the first radiator radiator series until the last team; And return water pipe in cb started with one last set of radiator is connected to the return water pipe.

if it is the ground heating heating way, personal advice at this time we want to choose the way for laying octopus type decorate, in the home kitchen or bathroom to select a suitable location to install heating diversity water, ground pipe from the diversity of water to the various rooms equipped, we should pay attention to each site tube circuit to control in 90 meters, the length of the loop between poor not greater than 5 meters; Cb for backwater pipe directly to ground heating on the diversity of water for the return water pipe.

J&T INDUSTRY CO.,LTD. undertakes bulk operations and specializes in undertaking corporate offers to cater the needs of different companies.
Review J&T INDUSTRY CO.,LTD.'s progress at regular intervals, so we can continue with the strategies that work well and change or eliminate the ones that don't give the results we are looking for.
The group's Quality Systems Manager (QSM) is responsible for ensuring that J&T INDUSTRY CO.,LTD. has in place systems that guarantee quality throughout the Group.